timing belt NISSAN 350Z 2007 Z33 Engine Control Workshop Manual

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: 2006 November2007 350Z
ENGINE CONTROL SYSTEM
INDEX FOR DTC ........................................................ 8
DTC No. Index ......................................................... 8
Alphabetical Index .................................................. 13
PRECAUTIONS ........................................................ 18
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 18
Precautions for Battery Service .............................. 18
Precautions for Procedures without Cowl Top Cover ... 18
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 18
Precaution .............................................................. 19
PREPARATION ......................................................... 22
Special Service Tools ............................................. 22
Commercial Service Tools ...................................... 23
ENGINE CONTROL SYSTEM .................................. 24
System Diagram ..................................................... 24
Multiport Fuel Injection (MFI) System .................... 25
Electronic Ignition (EI) System ............................... 27
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 28
AIR CONDITIONING CUT CONTROL ..................... 29
Input/Output Signal Chart ....................................... 29
System Description ................................................ 29
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 30
System Description ................................................ 30
Component Description .......................................... 31
CAN COMMUNICATION .......................................... 32
System Description ................................................ 32
EVAPORATIVE EMISSION SYSTEM ....................... 33
Description ............................................................. 33
Component Inspection ........................................... 36
Removal and Installation ........................................ 37
How to Detect Fuel Vapor Leakage ....................... 37
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................... 39
System Description ................................................ 39
Diagnostic Procedure ............................................. 40
Component Inspection ........................................... 42
POSITIVE CRANKCASE VENTILATION ................. 44Description .............................................................. 44
Component Inspection ............................................ 45
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS) ........................................................................ 46
Description .............................................................. 46
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 47
Introduction ............................................................. 47
Two Trip Detection Logic ........................................ 47
Emission-related Diagnostic Information ................ 48
Malfunction Indicator Lamp (MIL) ........................... 62
OBD System Operation Chart ................................ 65
BASIC SERVICE PROCEDURE ............................... 71
Basic Inspection ..................................................... 71
Idle Speed and Ignition Timing Check .................... 76
Procedure After Replacing ECM ............................ 76
VIN Registration ..................................................... 76
Exhaust Valve Timing Control Learning .................. 76
Accelerator Pedal Released Position Learning ...... 77
Throttle Valve Closed Position Learning ................. 77
Idle Air Volume Learning ........................................ 77
Fuel Pressure Check .............................................. 79
TROUBLE DIAGNOSIS ............................................ 81
Trouble Diagnosis Introduction ............................... 81
DTC Inspection Priority Chart ................................. 87
Fail-safe Chart ........................................................ 89
Symptom Matrix Chart ............................................ 90
Engine Control Component Parts Location ............ 94
Vacuum Hose Drawing .........................................100
Circuit Diagram .....................................................101
ECM Harness Connector Terminal Layout ...........103
ECM Terminals and Reference Value ...................103
CONSULT-III Function (ENGINE) .........................116
Generic Scan Tool (GST) Function .......................125
CONSULT-III Reference Value in Data Monitor ....127
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .132
Description ............................................................132
Testing Condition ..................................................132
Inspection Procedure ............................................132
Diagnostic Procedure ...........................................133
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-

EC-138
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Revision: 2006 November2007 350Z
17. CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of "DATA MONITOR" mode, and make sure that the indication is within the
SP value.
OK or NG
OK >>INSPECTION END
NG (More than the SP value)>>GO TO 18.
NG (Less than the SP value)>>GO TO 25.
18. DETECT MALFUNCTIONING PART
1. Check for the cause of large engine friction. Refer to the following.
–Engine oil level is too high
–Engine oil viscosity
–Belt tension of power steering, alternator, A/C compressor, etc. is excessive
–Noise from engine
–Noise from transmission, etc.
2. Check for the cause of insufficient combustion. Refer to the following.
–Valve clearance malfunction
–Intake valve timing control function malfunction
–Camshaft sprocket installation malfunction, etc.
>> Repair or replace malfunctioning part, and then GO TO 30.
19. CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

Crushed air ducts

Malfunctioning seal of air cleaner element

Uneven dirt of air cleaner element

Improper specification of intake air system
OK or NG
OK >> GO TO 21.
NG >> Repair or replace malfunctioning part, and then GO TO 20.
20. CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”, AND “B/FUEL SCHDL”
Select “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “B/FUEL SCHDL” in “SPEC” of "DATA MONITOR" mode, and
make sure that the each indication is within the SP value.
OK or NG
OK >>INSPECTION END
NG (“B/FUEL SCHDL” is more, “A/F ALPHA-B1”, “A/F ALPHA-B2” are less than the SP value)>>GO TO 21.
21. DISCONNECT AND RECONNECT MASS AIR FLOW SENSOR HARNESS CONNECTOR
1. Stop the engine.
2. Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and
then reconnect it again.
>> GO TO 22.